Thermo Scientific Barnstead GenPure xCAD Plus System Operating Instructions Manual Download Page 46

Page: 46 / 128

Installation

Installation of GenPure xCAD Plus system, wall version

GenPure

Thermo Scientific

Assemble the power pack and make the voltage
connection to the GenPure system.

See under

“Mounting the power pack (voltage

supply)”

page 48

Open the feedwater supply and switch the system
on.

The system is now ready for use.

Only feedwater that has been pretreated by
reverse osmosis, ion exchange or distillation is to
be used.

Step

Action

Figure

Feedwater
supply

Summary of Contents for Barnstead GenPure xCAD Plus System

































































































































Search results

Summary of Contents for Barnstead GenPure xCAD Plus System

Reviews:

Related manuals for Barnstead GenPure xCAD Plus System

Brands by name

Popular brands

Thermo Scientific Barnstead GenPure xCAD Plus System, Operating Instructions Manual

Search results

Summary of Contents for Barnstead GenPure xCAD Plus System

Reviews:

Related manuals for Barnstead GenPure xCAD Plus System

Brands by name

Popular brands