Thermo Scientific Barnstead GenPure xCAD Plus System Operating Instructions Manual Download Page 64

Page: 64 / 128

Operating elements xCAD Server and xCAD Client

Description of Display xCAD Server

GenPure

Thermo Scientific

Description of Display

xCAD Server

Shows actual
operating mode of
the system.

Display of the ultra pure
water resistance or
conductivity.

Shows that the temperature
compensation is switched on.

Shows the ON/OFF status
of the UV lamp operating
mode and of the
temperature

compensation.

Temperature
measurement

Shows the TOC content in
systems equipped with
TOC monitoring. If TOC
feature is not equipped it
will read

“ - - ”.

ON/OFF

switch

UV Key for manual
operation of the UV lamp.
Also enables values to be
changed in

the menu

mode.

The menu key brings you to the following system
parameters:

• Setting for the feedwater resistance

• Setting for the ultrapure water resistance

• UV lamp intensity and operating time

• Cartridge number and maintenance interval

• Rinsing

• Disinfection

• System errors display

• System errors print-out

• Unlocking the factory setting with your password.

Decreases numerical
values in the menu.

Confirms prompts

and selections.

Switches to Nonstop
mode for dispensing.
Increases numerical
values in the menu.

Summary of Contents for Barnstead GenPure xCAD Plus System

































































































































Search results

Summary of Contents for Barnstead GenPure xCAD Plus System

Reviews:

Related manuals for Barnstead GenPure xCAD Plus System

Brands by name

Popular brands

Thermo Scientific Barnstead GenPure xCAD Plus System, Operating Instructions Manual

Search results

Summary of Contents for Barnstead GenPure xCAD Plus System

Reviews:

Related manuals for Barnstead GenPure xCAD Plus System

Brands by name

Popular brands