Thermo Scientific Barnstead GenPure xCAD Plus System Operating Instructions Manual Download Page 38 | Manualshive

Page: 38 / 128

background image

7

Installation

Installation of GenPure xCAD Plus system, bench version

32

GenPure

Thermo Scientific

6

Connect the 8mm o.d hose to the rinse water
connection of the system (see step 5) and make a
gravity fall (pressureless) connection from the
system (connector 7) to the floor drain. The drain
to the sewer must be max. 1m (1.09 yards) above
the rinsing water connector of the Unit

7

a.

Connect the one end of the 0.31”

(8 mm) od hose to the xCAD backflow
connector on the system by unscrewing
the fitting. After this put the hose
through the fitting and mount the white
O-ring on it. Screw the fitting back to
the system.

b. The other end of the 0.31” (8 mm) o.d

hose you should connect to the xCAD
backflow connector of the xCAD Server.

Step

Action

Figure

White

O-ring

Fitting

Hose 8 mm
o.d

Rinsing water
connection

Connector GenPure
system

Fitting

Hose 0.31“
(8 mm) o.d

a)

Connector

xCAD

Server

Hose 0.31”
(8 mm) o.d

b)

White O-ring

«
...
36
37
38
39
40
...
»

Summary of Contents for Barnstead GenPure xCAD Plus System

































































































































Reviews:

No comments

Related manuals for Barnstead GenPure xCAD Plus System

MicroVersaTrip Plus

Brand: GE Pages: 20

Brand: GE Pages: 252

Brand: Balanced Body Pages: 12

Brand: Eagle Pro Pages: 6

Brand: GE Pages: 10

Brand: Landoll Pages: 34

Brand: Ecco Pages: 2

Brand: Landoll Pages: 94

Brand: Unex Pages: 5

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: TANACOM Pages: 27

Brand: iBACheck Pages: 2

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brand: Ravo Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands