Operating Instructions
120
Selecting the Setpoint for a Named Product
If the “Change Setpoint for XXXXX” Screen appears after
pressing the
Y
ES
soft key to select a named product, the named
product has been programmed with a setpoint range. Complete
the following steps to select a setpoint for the named product.
1.
The “Change Setpoint for XXXXX” Screen briefly
appears, then the “Current Setpoint of XXXXX &
Setpoint Range Is XX to XX” Screen will appear. See
Figure 88.
2.
Press the
+
/
-
or
E
XIT
soft keys accordingly as described
below. See Figure 88.
•
Press the
+
or
-
soft keys to change the current setpoint for
the named product and then go to step 3.
•
Press the
E
XIT
soft key to accept the current setpoint for
the named product. The Standard Display will appear with
the named product and setpoint. See Figure 88.
3.
If the
+
or
-
soft keys were pressed to change the current
setpoint for the named product, the “New Setpoint for
XXXXX Will Be” Screen will appear. See Figure 88.
4.
Press the
Y
ES
soft key to accept the new setpoint for the
named product.
NOTE: If the
N
O
key is pressed the setpoint will not be
changed and the display will return to the Standard
Display.
5.
The “Programming New Setpoint for XXXXX” Screen
will briefly appear. See Figure 88.
6.
The “New Setpoint Is XX” Screen briefly appears. See
Figure 88.
7.
The Standard Display appears with the named product and
new setpoint. See Figure 88.
NOTE: Pressing the
E
XIT
soft key at any point will return to
the Standard Display.
NOTE: If no keys are pressed for 30 seconds while in the
Named Product Changer Screens, the HMI will return to the
Standard Display.
Operating Instructions
120
Selecting the Setpoint for a Named Product
If the “Change Setpoint for XXXXX” Screen appears after
pressing the
Y
ES
soft key to select a named product, the named
product has been programmed with a setpoint range. Complete
the following steps to select a setpoint for the named product.
1.
The “Change Setpoint for XXXXX” Screen briefly
appears, then the “Current Setpoint of XXXXX &
Setpoint Range Is XX to XX” Screen will appear. See
Figure 88.
2.
Press the
+
/
-
or
E
XIT
soft keys accordingly as described
below. See Figure 88.
•
Press the
+
or
-
soft keys to change the current setpoint for
the named product and then go to step 3.
•
Press the
E
XIT
soft key to accept the current setpoint for
the named product. The Standard Display will appear with
the named product and setpoint. See Figure 88.
3.
If the
+
or
-
soft keys were pressed to change the current
setpoint for the named product, the “New Setpoint for
XXXXX Will Be” Screen will appear. See Figure 88.
4.
Press the
Y
ES
soft key to accept the new setpoint for the
named product.
NOTE: If the
N
O
key is pressed the setpoint will not be
changed and the display will return to the Standard
Display.
5.
The “Programming New Setpoint for XXXXX” Screen
will briefly appear. See Figure 88.
6.
The “New Setpoint Is XX” Screen briefly appears. See
Figure 88.
7.
The Standard Display appears with the named product and
new setpoint. See Figure 88.
NOTE: Pressing the
E
XIT
soft key at any point will return to
the Standard Display.
NOTE: If no keys are pressed for 30 seconds while in the
Named Product Changer Screens, the HMI will return to the
Standard Display.
Summary of Contents for SB-210+
