Thermann TH28ENR6L Installer Manual Download Page 4

Page: 4 / 52

Thermann Installer's Manual
Gas Continuous Flow Water Heaters

Installation Manual

Potential dangers from accidents during installation and use are divided into the following
three categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Earth

Requests to Installers

• In order to use the water heater safely, read this installation manual carefully, and follow the

installation instructions.

• Failures and damage caused by erroneous work or work not as instructed in this manual are not

covered by the warranty.

• Check that the installation was done properly in accordance with this Installation Manual upon

completion.

• After completing installation, please either place this Installation Manual in a plastic pouch and

attach it to the side of the water heater, or hand it to the customer to retain for future reference.

WARNING:

CAUTION

• The water heater must be commissioned including checking gas supply pressures at maximum

demand.

• The operation of the water heater should be explained including normal operation & regular

maintenance.

CAUTION

Condensing Models

Non Condensing Models

TH50ECR6N
TH50ECR6L

TH32ECR6N
TH32ECR6L

TH28ENR6N
TH28ENR6L

DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

WARNING

CAUTION

DANGER

Summary of Contents for TH28ENR6L





















































Search results

Summary of Contents for TH28ENR6L

Reviews:

Related manuals for TH28ENR6L

Brands by name

Popular brands

Thermann TH28ENR6L, Installer Manual

Search results

Summary of Contents for TH28ENR6L

Reviews:

Related manuals for TH28ENR6L

Brands by name

Popular brands