Thermann TH28ENR6L Installer Manual Download Page 26 | Manualshive

Page: 26 / 52

background image

Thermann Installer's Manual
Gas Continuous Flow Water Heaters

Plumbing Applications

Recirculation System

Cold Water Supply

Gas Supply

Aquastat(*3)

Pump Control Signal(*2) Only TH50ECR6 series

Relay for Pump

Hot Water

Optional 30-40 L
Storage Tank
(To alleviate cold water sandwich)

Globe
Valve

Pump(*1)

Expansion Tank
(Install according
to local code)

Fixtures

Hot Water Return

Notes:
1. Size the pump to provide a maximum of 7.5 L/min. through the system at 3m of head plus piping losses.
Adjust the flow using a globe valve and verify the flow rate with the maintenance monitors.
2. Pump Control Signal is the preferred method to control the recirculation pump.
A relay connection must be used. Only TH50ECR6 series.
If the Pump Control Signal is not used, an Aquastat may be used to control the pump.

3. Set the Aquastat to 5˚C below the set output temperature.

An aquastat is the minimum pump control requirement in order to maintain the full recirculation waranty.

Continuous Flow

Water Heater

26

«
...
24
25
26
27
28
...
»

Summary of Contents for TH28ENR6L





















































Reviews:

No comments

Related manuals for TH28ENR6L

FCD-JTHMG80-III

Brand: Haier Pages: 2

Little Sea-ox FCD-JTHC40-III (E)

Brand: Haier Pages: 6

Brand: Haier Pages: 18

Brand: Haier Pages: 23

Brand: Haier Pages: 20

Brand: Haier Pages: 2

Brand: Waterous Pages: 10

Brand: Oasis Pages: 18

Brand: Parker Pages: 44

Brand: TDRFORCE Pages: 12

Brand: Watson Marlow Pumps Pages: 95

Brand: Watson Marlow Pumps Pages: 87

Brand: Watson Marlow Pumps Pages: 127

Brand: ubbink Pages: 31

Brand: BIEMMEDUE Pages: 11

Tranquility Low-Profile Series

Brand: ClimateMaster Pages: 76

Excel Aqua Plus

Brand: TEFAL Pages: 8

Brand: Edwards Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands