manualshive.com logo in svg

Thermann TH28ENR6L, Installer Manual

The Thermann TH28ENR6L installer manual is a comprehensive guide for setting up and maintaining your water heater. This essential manual is available for free download at our website, ensuring you have access to the necessary resources for a seamless installation process. Get the most out of your Thermann product today.

Share
Download
background image

Multi-System Wiring (Use SC-401-6M)

45

Remote Controller

(Optional or Included)

Installation Guide

Requests to Installers

• In order to use the water heater safely, read this installation guide carefully, and follow the 

installation instructions.

• Failures and damage caused by erroneous work or work not as instructed in this manual 

are not covered by the warranty.

• Refer to the Installation Manual provided with the water heater for complete installation details.

Note

• Cutting too large of a hole on the wall may result in failure to properly secure the remote controller.
• Never fasten or loosen unnecessary screws in order to complete the remote controller installation.
• Be sure to check the positions of wall studs or other obstructions when determining the installation 

location for the remote controller.

• Secure the remote controller cable with approriate anchors, ties, etc.
• Wire the remote controller cable in an area where it will not be directly affected by heat.
• To embed the remote controller cable in concrete, brick, etc., enclose it in conduit in order to prevent 

the remote controller cable from becoming damaged.

• When penetrating a wall containing metal lath, prevent the lath from coming into contact with any 

metallic conduit used in order to prevent electrical interference.

• Wiring shall be provided so that the remote controller cable length is 100m or shorter.
• Connect the remote controller cable to the terminal block of the water heater (see Installation Manual 

provided with the water heater).

In order to use this product safely, read this installation manual carefully and follow the installation instructions.

• Potential dangers from accidents during installation and use are described below. 
  Closely observe these warnings, they are critical to your safety.

• Indoor use only. The remote controller is not water resistant. 

   Not suitable for installation in wet areas like shower recesses.
• The remote controller is not suitable for outdoor installation unless 

   installed in an enclosed and water proof box.

CAUTION

• Do not connect power to the system unit until the remote controller installation is complete.
• Be sure to fasten the mounting screws tightly by hand so that the remote controller will be secure.

*  Do not use electric drivers, impact drivers and so forth. Tightening with excessive force may cause 

the mounting bracket to be damaged and lead to failures.

• Install the remote controller on an even wall surface.

* Installing it on an uneven wall surface may cause the bracket to be damaged and lead to failures.

• This remote controller has a built-in speaker which can be damaged by metal shavings resulting in 

sound cracking.

  Keep the remote controller in a safe location prior to mounting it on the wall to prevent metal 

shavings from entering the remote controller.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not 

avoided, may result in minor or moderate injury.

CAUTION

Summary of Contents for TH28ENR6L





















































Reviews:

No comments

Related manuals for TH28ENR6L

Maag S Series Installation, Operation & Maintenance Manual preview
S Series
Brand: Maag Pages: 16
A.O. Smith 100 Series Installation & Operating Instructions Manual preview
100 Series
Brand: A.O. Smith Pages: 40
Samson DF100 Operation And Maintenance Manual preview
DF100
Brand: Samson Pages: 26
Daikin Altherma 3 GEO User Reference Manual preview
Altherma 3 GEO
Brand: Daikin Pages: 36
YAMADA DP Series Quick Manual preview
DP Series
Brand: YAMADA Pages: 84
Calpeda MXV-B Series Operating Instructions Manual preview
MXV-B Series
Brand: Calpeda Pages: 27
Watts LF919 Installation Instructions Manual preview
LF919
Brand: Watts Pages: 12
Gude GMP 100 4T Translation Of Original Operating Instructions preview
GMP 100 4T
Brand: Gude Pages: 62
Pelonis Safe-T FURNACE HC-445 Owner'S Manual preview
Safe-T FURNACE HC-445
Brand: Pelonis Pages: 6
Swann 5055322535865 Assembly Photo Manual preview
5055322535865
Brand: Swann Pages: 14
Warren rupp Sandpiper S05 Service & Operating Manual preview
Sandpiper S05
Brand: Warren rupp Pages: 22
First Sales FECS Series Installation Instructions And Owner'S Manual preview
FECS Series
Brand: First Sales Pages: 26
EXTOL 1429388 Manual preview
1429388
Brand: EXTOL Pages: 28
TERMA Alex-SX Installation Manual preview
Alex-SX
Brand: TERMA Pages: 2
Xylem Goulds AquaBoost Advanced Instruction Manual preview
Goulds AquaBoost Advanced
Brand: Xylem Pages: 36
Dimplex 6909910100 Service Manual preview
6909910100
Brand: Dimplex Pages: 8
EINHELL HWW 4600 NIRO-NIRO Operating Instructions Manual preview
HWW 4600 NIRO-NIRO
Brand: EINHELL Pages: 40
Tuxhorn tubra- PGS multi Assembly And Operating Manual preview
tubra- PGS multi
Brand: Tuxhorn Pages: 60

Brands by name

Popular brands

Load more brands