Thermann TH28ENR6L Installer Manual Download Page 2 | Manualshive

Page: 2 / 52

background image

Thermann Installer's Manual
Gas Continuous Flow Water Heaters

To be installed and serviced only by an authorised person.

This appliance is not suitable for use as a pool heater.

The "authorised installing person" is responsible for:
1. Correct commissioning of this appliance
2. Ensure unit performs to the specification stated on the data label
3. Demonstrate operation of unit to customer before leaving
4. Hand these instructions to customer

This appliance must be installed in accordance with the manufacturer's installation instructions all Local
Building, Water and Gas fitting regulations (AS/NZS3500.4, AS/NZS 5601, AS/NZS3000).

This appliance delivers water in excess of 50 Degrees C. Ensure that suitable devices such as Tempering
Valves are installed in lines servicing Sanitation areas per AS3500.4.

Failure to install this appliance in accordance with these installation instructions may void
warranty.

In the interest of continued product improvement, Reece Manufacturing reserves the right to alter these
specifications without notice.

2

«
1
2
3
4
...
»

Summary of Contents for TH28ENR6L





















































Reviews:

No comments

Related manuals for TH28ENR6L

Brand: laguna Pages: 24

Brand: Navien Pages: 108

Brand: vacuubrand Pages: 76

Water Solutions 3098 Series

Brand: Zoeller Pages: 4

Aquanot Spin 508

Brand: Zoeller Pages: 2

Brand: Zoeller Pages: 11

Brand: Zip Pages: 18

Brand: A.O. Smith Pages: 31

Brand: ATC Pages: 8

Brand: Desa Pages: 12

Brand: Speck Pages: 24

MPXI11MULTIPC18

Brand: Master Pumps Pages: 32

Brand: Hamilton Beach Pages: 14

Brand: Oceanic Pages: 43

Lunaled Creative Set

Brand: Oase Pages: 48

JUNG PUMPEN JP09179/3

Brand: Pentair Pages: 42

Brand: Xylem Pages: 20

Brand: Xylem Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands