background image

4000305-14

WARNING: If the information in these 
instructions is not followed exactly, a 

fi

 re 

or explosion may result causing property 
damage, personal injury or loss of life.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light the appliance.
• Do not touch any electrical switch; do not 

use any phone in your building.

• Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 
supplier’s instructions.

• If you cannot reach your gas supplier, call 

the 

fi

 re department.

This appliance is only for use with the type 
of gas indicated on the rating plate. This 
appliance is not convertible for use with 
other gases, unless a certi

fi

 ed kit is used.

This appliance is a domestic room-heating 
appliance. It must not be used for any other 
purposes such as drying clothes, etc.

This appliance is suitable for installation in a 
bedroom or bed sitting room.

Manufactured by

MILES INDUSTRIES LTD.

British Columbia, Canada

www.miles

fi

 replaces.com

Installation & Operating Instructions

Do not store or use gasoline or other 

fl

 ammable vapors and liquids in the vicinity 

of this or any other appliance.

Installation and service must be performed 
by a quali

fi

 ed installer, service agency or the 

gas supplier.

This appliance may be installed in an 
after-market permanently located, 
manufactured (mobile) home where not 
prohibited by local codes.

Models 530XAN/XAP (logs)

Models 530XCN/XCP (coals)

Direct Vent Gas Fireplace Heater

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Massachusetts: The piping and 

fi

 nal 

gas connection must be performed by a 
licensed plumber or gas 

fi

 tter in the State of 

Massachusetts. Also, see Carbon Monoxide 
Detector requirements under “Safety and 
Warning Information” on page 5.

This manual contains instructions to install the

 ENGINE ONLY. 

A front trim kit is

 

REQUIRED 

to install the engine as it affects the framing cavity and position of the 

engine. 

Refer to the manual supplied with the front for framing and 

fi

 nishing.

Please read this manual BEFORE installing and operating this appliance.

©2007, Miles Industries Ltd. All rights reserved.

Summary of Contents for 530XAN/XAP





































Reviews: