Texmate Tiger 320 DI-602AE Manual Download Page 38

Page: 38 / 44

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com

Page 38

Apr-21-2016 DI_602A 320 DS (NZ313)_April 2016

Analog Outputs

Pin 16

– Positive (+) analog output 1.

Pin 17

– Negative (–) analog output 1 and 2.

Pin 18

– Positive (+) analog output 2.

Serial Outputs RS-232 or RS-485

Pin No.

RS-232

RS-485

Reserved for future use

RXD. Received Serial

TXD. Transmitted Serial

+5 VDC to power external converters

Isolated Ground

Reserved for future use

B (Low)

A (High)

+5 VDC to power external converters

Isolated Ground

Reserved for future use

Carrier Board Output Pins

Order Code

OR45
OR46

Options

SP6

SP5

SP4

SP3

SP2 SP1

SP3 SP2 SP1

SP4

SP5

SP6

Relay Modules with five or six 4A Form A Relays

Options

Order Code

OR11
OR12

OR23

OR14

10A

OR15

OR16

SP2

SP4

SP1

SP3

SP3

SP1

SP4

SP2

Relay Modules with up to two 4/5A Form A Relays,

and up to two 9/10A Form C Relays

Options

Order Code

OR51

OR52

OR53

OR54

210mA

SP4

SP3

SP2

SP1

SP4

SP3

SP2

SP1

Relay Modules with up to 4 Independent 300V

(210mA DC only) SSRs

Options

Order Code

OR31

OR32

OR33
OR34

SP4

SP3

SP2

SP1

SP1

SP2

SP3

SP4

Relay Modules with up to four 5A Form A Relays

Ethernet

–

The Ethernet carrier board has the same ana-

log output pins, with 10/100Base-T Ethernet (RJ-45 Socket).

Order Code

OR71

OR72

Options

SP6

SP5

SP4

SP3

SP2

SP1

0 to 5V

0 to V+

0 to 5V

0 to V+

0 to 5V

0 to V+

0 to 5V

0 to V+

0 to 5V

0 to V+

0 to 5V

0 to V+

Open Collector / TTL / 5VDC Output (50 mA)

SP1

+5VDC

V+

ISO

GND

SP3 SP2

SP4

SP6 SP5

5VDC @ 30mA

Relay and Logic I/O Modules

22 21 20

Serial Output

RJ-6 Socket

Order Code

Removable Flash Memory Card

Two NPN Open Collector Outputs

Max 5VDC @ 30mA

OR91

Options

Flash Card Memory Module

MODULE WITH 4 MEG MEMORY

SP2

SP1

Summary of Contents for Tiger 320 DI-602AE













































Search results

Summary of Contents for Tiger 320 DI-602AE

Reviews:

Brands by name

Popular brands

Texmate Tiger 320 DI-602AE, Manual

Search results

Summary of Contents for Tiger 320 DI-602AE

Reviews:

Brands by name

Popular brands