manualshive.com logo in svg

Texmate Tiger 320 DI-602AE, Manual

Share
Download
Texmate Tiger 320 DI-602AE Manual Download Page 21

Page 21

Apr-21-2016 DI-602A 320 DS (NZ313)_UL_April 2016

Texmate, Inc. Tel. (760) 598-9899  •  www.texmate.com

To Step 7

From Step 6

Step 1

Step 2

Step 3

Step 4

Step 5

Step 7

Step 8

Step 9

Pass Brightness Mode
and Calibration
Modes and enter
Code 1

Set Code 1 to [X71]

Exit Code 2. Return to
Operational Display

Select [X0X] to leave
Code 1

Save Last Digit Text
Character setting

CONFIGURE

1st Digit  = X Not relevant
2nd Digit  = 7 Selects
text character mode
3rd Digit  = 1 Selects
Channel 1

Enter Brightness Mode

LAST DIGIT

0 

Result

1 Channel 1
2 Channel 2
3 Channel 3
4 Channel 4
5 Default Display
6 Total 1
7 Total 2

TEXT CHARACTER

Select Text Character
[C] from the options
listed in the diagram
above

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Operational Display

Press

at same

time

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Press

2

OR

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Press

1

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

OR

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Press

1

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Press

at same

time

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Operational Display

OR

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Step 6

Example

SP1

SP3

SP4

SP5

SP6

SP2

F1

P

F2

Press

1

The following example procedure describes how to select the 
last digit text character.

Example Procedure:

Configure the Channel 1 with C as its last digit text character 
(for °C) by setting Code 1 to [

X71

] to enter the Select Last Digit 

Text Character Mode. See diagram opposite.

Configure Last Digit Text Character Procedure

START HERE

Initial Setup Procedures

[CodE_1] - Display Configuration continued

Use the 

 button to cycle through the 

m e n u , 

and the 

 button to cycle back.

Select Last Digit Text Character

Summary of Contents for Tiger 320 DI-602AE













































Reviews:

No comments

Brands by name

Popular brands

Load more brands