Tennant 235D User Manual Download

Page: 34 / 203

OPERATION

235 MM331 (3--93)

2-16

6. Lower the machine onto the jack stands.

7. Check to make sure the machine is secure.

8. Service the machine as required.

9. When finished servicing the machine, raise

the machine off the jack stands.

10. Remove the jack stands from under the

machine.

11. Lower the machine.

12. Remove the blocks from the tires.

MACHINE TIE-DOWNS

The machine may be tied down at each corner of

the main frame using the tie-down brackets

supplied in the tie-down kit.

03372

FRONT TIE-DOWN LOCATION

A. Tie-Down Bracket

When transporting the machine on a trailer or in a

truck, be sure to set the machine parking brake

and block the machine tires to prevent the

machine from rolling.

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands