Tennant 235D User Manual Download

Page: 55 / 203

MAINTENANCE

3-19

235 MM331 (3--93)

10. Install the new or cleaned filter element so

the fins on the element are at the intake end

of the air cleaner. Use care so the fins are

not damaged. Tighten the wing nut attaching

the element.

11. Install the dust cap with the tab down.

Secure the cap with the latches. Check all

intake hose connections for leaks or

abrasion.

03484

DUST CAP

A. Dust Cap

B. Tab

C. Housing

12. Close the seat support.

FUEL SYSTEM

FUEL SYSTEM
The diesel fuel system is made up of five basic

components which are: fuel tank, fuel water trap

filter, fuel pump, injection pump, and injectors.

Fuel flows from the fuel tank through the fuel

water trap filter. The water trap filter separates

water and impurities from the fuel. From the fuel

water trap filter, fuel is drawn through the electric

fuel pump and pumped to the injection pump. The

injection pump pressurizes and sends fuel to the

injectors. The injectors atomize and inject proper

amounts of fuel into the combustion chamber at

the proper times. Excess fuel is returned to the

fuel tank through an overflow pipe.

FUEL WATER TRAP FILTER
The fuel water trap filter separates water and

impurities from the fuel. It is located next to the

fuel tank. The bottom portion of the unit is the

water trap. The middle portion is the filter

element.

Drain the water trap of water daily. To drain the

water trap, loosen the drain knob on the bottom of

the unit. First water, then diesel fuel will drain.

Tighten the drain knob when diesel fuel appears.

Replace the fuel filter element and clean the water

trap after every 400 hours of operation.

TO REPLACE FUEL FILTER ELEMENT

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Open the seat support.

3. Close the fuel drain cock.

4. Loosen the water trap vent plug and open

the drain valve to drain diesel fuel.

03494

FUEL WATER TRAP FILTER

A. Filter Head

B. Vent Plug

C. Filter Element

D. Water Trap Bowl

E. Fuel Drain Cock

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands