Tennant 235D User Manual Download Page 56

Page: 56 / 203

MAINTENANCE

235 MM331 (3--93)

3-20

5. Remove the filter element and the water trap

from the filter head.

6. Remove the water trap bowl from the filter

element.

7. Clean the water trap bowl.

8. Lubricate the o-ring and spin the water trap

bowl onto the new filter element.

9. Lubricate the o-ring and spin the filter

element and water trap onto the filter head.

10. Open the fuel drain cock.

11. Bleed the fuel lines of air as described in

PRIME FUEL SYSTEM

12. Close the seat support.

PRIMING FUEL SYSTEM
Priming the fuel system removes pockets of air in

the fuel lines and fuel components. Air in the fuel

system will prevent smooth engine operation.

Prime the fuel system after running out of fuel,

changing fuel filter elements or repairing a fuel

system component.

TO PRIME FUEL SYSTEM

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Fill the fuel tank.

3. Open the seat support.

4. Open the air vent on top of the fuel injection

pump.

03482

FUEL INJECTION PUMP

A. Injection Pump

B. Air Vent

5. Turn the ignition switch to the “ON”position

(this operates the electric fuel pump) until a

steady stream of fuel flows from the vent.

6. Close the air vent.

7. Close the seat support.

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands