Tennant 235D User Manual Download Page 21

Page: 21 / 203

OPERATION

2-3

235 MM331 (3--93)

PREPARATION FOR OPERATION

AFTER UNCRATING AND BEFORE

OPERATING MACHINE:

1. Check the machine for shipping damage.

2. Read this manual carefully before operating

or servicing the machine.

FOR SAFETY: Do Not Operate Machine,

Unless Operation Manual Is Read And

Understood.

3. Check the hydraulic fluid level in the

hydraulic fluid reservoir. See

HYDRAULICS

in the

MAINTENANCE

section.

4. Check the main brush adjustment. See

BRUSHES

in the

MAINTENANCE

section.

5. Check the engine oil level. See

ENGINE

the

MAINTENANCE

section.

6. Fill the fuel tank on the machine.

FOR SAFETY: When Servicing Machine, Keep

Flames And Sparks Away From Fuel System

Service Area. Keep Area Well Ventilated.

7. Check the radiator coolant level in the

coolant tank.

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands