Tennant 235D User Manual Download

Page: 64 / 203

MAINTENANCE

235 MM331 (3--94)

3-28

11. Replace the belt guard.

12. Lower the seat support.

MAIN BRUSH BELT

The main brush belt transfers power from the

accessories pump to the main brush. The belt is

tensioned by a belt idler spring. A stop bolt is

used to remove tension from the belt when the

main brush is raised.

TO REPLACE MAIN BRUSH BELT

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Raise the main brush.

3. Open the seat support.

4. Remove the vacuum fan belt guard.

5. Remove the left side access door.

6. Hold the idler spring arm back and remove

the belt.

03377

MAIN BRUSH BELT

A. Idler Spring Arm

B. Main Brush Belt

C. Stop Bolt

7. Position the new belt on the belt sheaves.

8. Replace the vacuum fan belt guard.

9. Lower the seat support.

10. Start the machine and lower the main brush.

Then raise the brush. The brush should stop

turning within seconds of being raised. If the

belt is too tight, the brush will continue to

turn. If the belt is too loose, it may jump off

the idler or driven sheave. Turn the belt stop

bolt to adjust belt tension.

11. Replace the left side access door.

FAN BELT

The fan belt is driven by the crankshaft sheave

and drives the alternator and the radiator fan.

Check the belt condition and tension after every

200 hours of operation. The belt is properly

tensioned when the belt deflects 0.28 in (7 mm)

from a force of 22 lb (10 kg) applied at belt

midpoint.

TO REPLACE AND ADJUST FAN BELT

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Open the seat support.

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands