Tennant 235D User Manual Download Page 45

Page: 45 / 203

MAINTENANCE

3-9

235 MM331 (3--93)

TO REPLACE FILTER ELEMENT

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Open the seat support.

03395

HYDRAULIC FLUID FILTER

A. Filter Element

3. Unthread and discard the hydraulic fluid filter

element.

4. Apply a thin coat of hydraulic fluid to the seal

of the new hydraulic fluid filter element.

5. Thread and hand tighten the new hydraulic

fluid filter element on the filter head.

6. Close the seat support.

7. Operate the machine and check for leaks.

Correct any leaks found.

8. Check the hydraulic fluid reservoir level and

fill as required.

HYDRAULIC PUMPS

The machine propelling pump is a variable

displacement hydraulic piston pump. It is driven

by the engine via a dual belt.

The machine accessories pump is a hydraulic

gear pump. It is driven by a belt from the

propelling pump sheave.

After repairing or replacing a hydraulic pump, or

when system contamination is likely, change the

hydraulic fluid in the reservoir and the hydraulic

fluid filter. Then the proper start and break-in

procedure must be followed to prevent possible

damage to the pump. Replace the hydraulic fluid

filter after the first hour of operation.

TO START

AND BREAK-IN HYDRAULIC PUMP

outlines the

procedure.

TO START AND BREAK-IN HYDRAULIC PUMP

1. Stop the engine, set the machine parking

brake and block the front tires of the

machine.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Jack up the rear of the machine at the

designated locations.

FOR SAFETY: When Servicing Machine, Block

Machine Tires Before Jacking Machine Up.

3. Block up the machine with jack stands in the

designated locations. Make sure the rear tire

clears the floor by 2 in (50 mm) and all

obstacles within a 24 in (610 mm) radius.

FOR SAFETY: When Servicing Machine, Jack

Machine Up At Designated Locations Only.

Block Machine Up With Jack Stands.

4. Fill the hydraulic fluid reservoir with 3 gal

(11 L) of new, approved hydraulic fluid.

5. Fill the hydraulic pump through the case

drain port with hydraulic fluid.

6. Remove the engine coil wire from the engine

distributor or turn off fuel flow.

7. Operate the engine starter motor for three

10 second periods.

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands