Tennant 235D User Manual Download

Page: 69 / 203

MAINTENANCE

3-33

235 MM331 (3--94)

TO REMOVE AND REPLACE HOPPER DUST

FILTER

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Unlatch the two filter cover latches and

remove the filter cover.

3. Remove the two assembly bolts on each

side of the filter and slide the assembly

back. Remove the dust filter.

03389

DUST FILTER

A. Dust Filter

B. Shaker Motor Assembly

C. Hold-Down Screws

D. Assembly Bolts

4. Inspect and clean or replace the dust filter.

5. Position the dust filter in the filter frame with

the arrows on the label pointing up.

6. Secure the filter with the shaker motor

assembly.

7. Check the two filter hold-down screws. They

should clear the filter by 0.03 in (1 mm).

8. Secure the filter cover on the filter frame

with the two latches.

9. Check the hopper cover seal. It should be

slightly compressed.

Summary of Contents for 235D












































































































































































































Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands

Tennant 235D, User Manual

Search results

Summary of Contents for 235D

Reviews:

Related manuals for 235D

Brands by name

Popular brands