Telestream PRISM MPD Installation And Safety Instructions Download

Page: 43 / 50

Operations

Power-on and Power-off Procedures

PRISM MPS Installation and Safety Instructions

Note:

The power button illuminates during the power-on sequence and then turns

off during normal instrument operation.

Power-off Procedure

Press the power button

to turn the instrument off.

CAUTION: To prevent data loss, we strongly recommend you first shut down the

instrument before disconnecting the power cord. Press the power button or

select

Settings

Utilities

Power

, and then

Power Down Now

To completely remove power from the instrument, disconnect the power cord from

the instrument. The power cord has a locking mechanism to keep it attached to the

instrument. Push the button on the cord housing to release the locking

mechanism.

Summary of Contents for PRISM MPD



















































Search results

Summary of Contents for PRISM MPD

Reviews:

Related manuals for PRISM MPD

Brands by name

Popular brands

Telestream PRISM MPD, Installation And Safety Instructions

Search results

Summary of Contents for PRISM MPD

Reviews:

Related manuals for PRISM MPD

Brands by name

Popular brands