Tektronix AWG7000 Series, Service Manual

Page: 99 / 140

Troubleshooting
AWG7000 Series Service Manual
4-47
131000002 HwDiagClockPll 1GHz PLL Locked AWG10G, CLK10G AWG10G: U1000
CLK10G: U3200
131000003 HwDiagClockPll 4.9GHz YIG tuning error AWG10G, CLK10G AWG10G: U1000, U1040
CLK10G: U3200,U3250,Y3100,Y3280
131000004 HwDiagClockPll 4.9GHz PLL Unlocked AWG10G, CLK10G AWG10G: U1000, U1040
CLK10G: U3200,U3250,Y3100,Y3280
131000005 HwDiagClockPll 10.1GHz YIG tuning error AWG10G, CLK10G AWG10G: U1000, U1040
CLK10G: U3200,U3250,Y3100,Y3280
131000006 HwDiagClockPll 10.1GHz PLL Unlocked AWG10G, CLK10G AWG10G: U1000, U1040
CLK10G: U3200,U3250,Y3100,Y3280
140000000 The error occurred in the EEPROM read. 1st= FST
2nd= SND
FST: the data that is received from EEPROM at the first read
check
SND: the data that is received from EEPROM at the second
read check, which is implemented after writing 0x55 to
EEPROM
OUT10G OUT10G-CH1: U500, U550
140000001 Message varies depending on the situation. OUT10G OUT10G-CH1: U500, U550
1410P0001 Analog Level Diag CH1 positive (negative) 5db attenuator
failed. expected 0.56234, actual xxxxx OUT10G OUT10G: K610, K710
1410P0002 Analog Level Diag CH1 positive (negative) 5db attenuator
failed. expected 0.56234, actual xxxxx OUT10G OUT10G: K610, K710
1410P0003 Analog Level Diag CH1 positive (negative) 10db attenuator
failed. expected 0.31627, actual xxxxx OUT10G OUT10G: K620, K720
1410P0004 Analog Level Diag CH1 positive (negative) 20db attenuator
failed. expected 0.100000, actual xxxxx OUT10G OUT10G: K630, K730
1410P0005 Analog Level Diag CH1 positive (negative) 50mhz filter
failed. expected 0.992, actual xxxxx OUT10G OUT10G: K660, K760
1410P0006 Analog Level Diag CH1 positive (negative) 200mhz filter
failed. expected 0.998, actual xxxxx OUT10G OUT10G: K670, K770
1410P0007 Analog Level Diag CH1 positive (negative) amplitude cal
failed. expected 2.07, actual xxxxx OUT10G OUT10G: U800
1410P0008 Analog Level Diag CH1 positive (negative) hfd dac
reference failed. AWG10G AWG10G: U100A, U150A
1410P0009 Analog Level Diag CH1 positive (negative) output offset
failed. expected 0.50V(0.0V), actual xxxxx AWG10G OUT10G: U900, U910, U920
141000010 Analog Level Diag CH1 internal offset 8bit failed. expected
0.0mV, actual xxxxxmV AWG10G AWG10G: U100A, U150A
141000011 Analog Level Diag CH1 internal offset 10bit failed. expected
0.0mV, actual xxxxxmV AWG10G AWG10G: U100A, U150A
141000012 Analog Level Diag CH1 can't find 8bit outamp offset cross
point. expected 0.0mV, actual pos: xxxxxmV, neg: xxxxxmV AWG10G AWG10G: U100A, U150A
141000013 Analog Level Diag CH1 can't find 10bit outamp offset cross
point. expected 0.0mV, actual pos: xxxxxmV, neg: xxxxxmV AWG10G AWG10G: U100A, U150A
141000015 Analog Level Diag CH1 5db attenuator gain balance failed. OUT10G OUT10G: K610, K710
141000016 Analog Level Diag CH1 5db attenuator gain balance failed. OUT10G OUT10G: K610, K710
Table 4-6: Diagnostics error (cont.)
Error code Error log message Possible defect
on board Note