manualshive.com logo in svg

Tektronix ATEC TekRanger 2, User Manual

Share
Download
Tektronix ATEC TekRanger 2 User Manual Download Page 154

Specifications

5–8

TFS3031 TekRanger/TekRanger 2 User Manual

Table 5–8: Certifications and Compliances 

Category

Standards or Description

EC Declaration of
Conformity – EMC

Meets intent of Directive 89/336/EEC for Electromagnetic
Compatibility. Compliance was demonstrated to the following
specifications as listed in the Official Journal of the European
Union:

EN 50081-1 Emissions:

EN 55022

Class B Radiated and Conducted Emissions

EN 60555-2

AC Power Line Harmonic Emissions

EN 50082-1 Immunity:

IEC 801-2

Electrostatic Discharge Immunity

IEC 801-3

RF Electromagnetic Field Immunity

IEC 801-4

Electrical Fast Transient/Burst Immunity

IEC 801-5

Power Line Surge Immunity

Australia/New Zealand
Declaration of
Conformity – EMC

Complies with EMC provision of Radiocommunications Act 
per the following standard(s):

AS/NZS 2064.1/2

Industrial, Scientific, and Medical
Equipment:1992

EMC Compliance

Meets the intent of Directive 89/336/EEC for Electromagnetic
Compatibility when it is used with the product(s) stated in the
specifications table. Refer to the EMC specification published for

the stated products. May not meet the intent of the directive if used

with other products.

FCC Compliance

Emissions comply with FCC Code of Federal Regulations 47, Part
15, Subpart B, Class A Limits.

EC Declaration of
Conformity – Low
Voltage

Compliance was demonstrated to the following specification as
listed in the Official Journal of the European Union:

Low Voltage Directive 73/23/EEC, amended by 93/69/EEC

EN 61010-1:1993 

Safety requirements for electrical  equipment for 
measurement, control,  and laboratory use.

U.S. Nationally
Recognized Testing
Laboratory Listing

UL3111-1 

Standard for electrical measuring and test  equipment.

Specifications

5–8

TFS3031 TekRanger/TekRanger 2 User Manual

Table 5–8: Certifications and Compliances 

Category

Standards or Description

EC Declaration of
Conformity – EMC

Meets intent of Directive 89/336/EEC for Electromagnetic
Compatibility. Compliance was demonstrated to the following
specifications as listed in the Official Journal of the European
Union:

EN 50081-1 Emissions:

EN 55022

Class B Radiated and Conducted Emissions

EN 60555-2

AC Power Line Harmonic Emissions

EN 50082-1 Immunity:

IEC 801-2

Electrostatic Discharge Immunity

IEC 801-3

RF Electromagnetic Field Immunity

IEC 801-4

Electrical Fast Transient/Burst Immunity

IEC 801-5

Power Line Surge Immunity

Australia/New Zealand
Declaration of
Conformity – EMC

Complies with EMC provision of Radiocommunications Act 
per the following standard(s):

AS/NZS 2064.1/2

Industrial, Scientific, and Medical
Equipment:1992

EMC Compliance

Meets the intent of Directive 89/336/EEC for Electromagnetic
Compatibility when it is used with the product(s) stated in the
specifications table. Refer to the EMC specification published for

the stated products. May not meet the intent of the directive if used

with other products.

FCC Compliance

Emissions comply with FCC Code of Federal Regulations 47, Part
15, Subpart B, Class A Limits.

EC Declaration of
Conformity – Low
Voltage

Compliance was demonstrated to the following specification as
listed in the Official Journal of the European Union:

Low Voltage Directive 73/23/EEC, amended by 93/69/EEC

EN 61010-1:1993 

Safety requirements for electrical  equipment for 
measurement, control,  and laboratory use.

U.S. Nationally
Recognized Testing
Laboratory Listing

UL3111-1 

Standard for electrical measuring and test  equipment.

Summary of Contents for ATEC TekRanger 2















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands