Technicolor TB30 Administrator'S Manual Download Page 61 | Manualshive

Page: 61 / 266

background image

TB30s SIP Administrator Guide v1.3

Page 54 of 259

Part 7 Auto-Provisioning

The

automatic provisioning

requires one DHCP server and one HTTP/TFTP server.

The

USB

automatic provisioning

requires one USB disk.

Please find below the way to provision your IP Phone.

Automatic phone provisioning with TFTP

The automatic phone provisioning is particularly adapted to the provision of several phones at
the same time, of any large-scale deployment environment. Auto-provisioning is achieved using
2 well-known protocols: Dynamic Host Control Protocol (DHCP) and Trivial File Transfer
Protocol (TFTP).

Simply follow next steps to provision your IP Phone:

Needed:

1 DHCP server which one can manage the options
1 TFTP server
1 TB30 (SIP or MGCP)

Several files which one can need (correctly filled) are:

SIP: File INF
Firmware
File « common_config »

File MAC specific

  File « Telconf »

MGCP: File INF
     Firmware
Files Deck
File« common_config »

File MAC specific

File « TelConf »

(See examples of these files in Appendix.)

«
...
59
60
61
62
63
...
»

Summary of Contents for TB30











































































































































































































































































Reviews:

No comments

Related manuals for TB30

Brand: Panasonic Pages: 312

Brand: Samsung Pages: 2

Galaxy MEGA SGH-I527

Brand: Samsung Pages: 237

Galaxy j7 Crown

Brand: Samsung Pages: 33

Brand: Samsung Pages: 39

Brand: Samsung Pages: 28

Exclaim SPH-M550

Brand: Samsung Pages: 226

Brand: Samsung Pages: 12

E630 - SGH Cell Phone

Brand: Samsung Pages: 103

DoubleTime SGH-I857

Brand: Samsung Pages: 225

Delve SCH-R800 Series

Brand: Samsung Pages: 180

Brand: Samsung Pages: 10

Brand: Samsung Pages: 7

Galaxy Music GT-S6010

Brand: Samsung Pages: 39

Byline SCH-R310 Serie

Brand: Samsung Pages: 119

Brand: Samsung Pages: 100

Brand: Samsung Pages: 2

Brand: Samsung Pages: 148

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands