manualshive.com logo in svg

Technicolor TB30, Administrator'S Manual

The Technicolor TB30 Administrator's Manual is a comprehensive and free resource for optimizing your TB30 experience. Download this essential manual from manualshive.com to access step-by-step instructions, troubleshooting tips, and in-depth explanations, ensuring seamless operation and maximum productivity with your Technicolor TB30 device.

Share
Download
background image

 

 
TB30s SIP Administrator Guide v1.3  

 

Page 233 of 259 

Part 12 Telnet Activation 

 

Introduction 

This  part  reviews  and  summarizes  TB30  Telnet  commands  useful  for  remote 
management of the phone. 
 
Other  commands  (like  configuration  of  the  phone‟s  parameters)  are  described  in 
another  Technical  document:  “TB30  Config  file  Syntax”.    It  is  issued  in  the  firmware 
release package.  

Enable Telnet service 

 
By default, the Telnet service is disabled for security reasons. 
So  the  Telnet  service  must  be  enabled  before  trying  to  open  a  telnet  session  on  the 
phone.  
 
Enter the following URL on you web browser:  
http://ip_address_of_the_phone/telnet.html 

 

Then enter the username and password (same as the web interface):  
Username (default): administrator  
Password (default): 784518 
 

 

 

Summary of Contents for TB30











































































































































































































































































Reviews:

No comments

Related manuals for TB30

Kyocera Sprint Torque Booklet preview
Sprint Torque
Brand: Kyocera Pages: 32
Grandstream Networks GRP2612/G Quick Installation Manual preview
GRP2612/G
Brand: Grandstream Networks Pages: 25
Alcatel One Touch 818 User Manual preview
One Touch 818
Brand: Alcatel Pages: 52
FutureCall FC-7677-2 User Manual preview
FC-7677-2
Brand: FutureCall Pages: 11
Yezz 5M2 User Manual preview
5M2
Brand: Yezz Pages: 80
Beacon BTAR Manual preview
BTAR
Brand: Beacon Pages: 2
jablotron JA-62GSM Installation Manual preview
JA-62GSM
Brand: jablotron Pages: 11
Samsung SCH-U550 Manual Del Usuario preview
SCH-U550
Brand: Samsung Pages: 145
Samsung Intensity SCH-u450 User Manual preview
Intensity SCH-u450
Brand: Samsung Pages: 142
Samsung SCH-W480 User Manual preview
SCH-W480
Brand: Samsung Pages: 26
Samsung SM-J400G User Manual preview
SM-J400G
Brand: Samsung Pages: 79
Samsung SM-J327V User Manual preview
SM-J327V
Brand: Samsung Pages: 39
Samsung SM-J327T User Manual preview
SM-J327T
Brand: Samsung Pages: 38
Samsung SGHA637 User Manual preview
SGHA637
Brand: Samsung Pages: 166
Samsung SGHT679M User Manual preview
SGHT679M
Brand: Samsung Pages: 45
Panasonic KX TPA 65 Quick Reference Manual preview
KX TPA 65
Brand: Panasonic Pages: 14
Mitel 5215 User Manual preview
5215
Brand: Mitel Pages: 42
LogicMark CaretakerSentry 40911 Dealer Set-Up & Programming Instructions preview
CaretakerSentry 40911
Brand: LogicMark Pages: 24

Brands by name

Popular brands

Load more brands