Technicolor TB30 Administrator'S Manual Download Page 246

Page: 246 / 266

TB30s SIP Administrator Guide v1.3

Page 239 of 259

Parameter in config file & CLI

Please use >cwmp in command line. It will list the command which can be used to do some
setting. Any syntax please refer to the file TB30

S_Config File

CWMP flow

File System

Parameter

Valid values

Default

CLI

Description

CWMPFlag

0 disable
1 enable

cwmp set
flag 1/0

Enable/disable cwmp TR069

CWMPACS

URL

empty

cwmp set
acs acsurl

URL of the TR-069 ACS. This is
the URL the phone will send TR-
069 messages to. Please contact
your ACS vendor to find out
about this URL.

CWMPACSUser

STRING

empty

cwmp set
user
username

Username for HTTP
authentication against the ACS

CWMPACSPassword

STRING

empty

cwmp set
pwd
password

Password for HTTP
authentication against the ACS

CWMPConnReqUser

STRING

empty

cwmp set
requser
username

ACS's Connection-Request User
Name

CWMPConnReqPassword STRING

empty

cwmp set
reqpwd
passward

ACS's Connection-Request
Password

CWMPPeriodicFlag

0 disable
1 enable

cwmp set
pflag 1/0

cwmp set pflag <on(1)/off(0)>

CWMPPeriodicInterval

Periodic
Interval

180

cwmp set
interval

CPE will send INFORM according
to this period time

TR111STUNEnable

0 disable
1 enable

cwmp set
stunflag 0/1

Enable or disable the stun

TR111STUNSrvAddr

empty

cwmp set
stunserver
IP

Set CPE stun server address

TR111STUNSrvPort

Port

3478

cwmp set

stunport
xxxx

Set CPE stun port

TR111STUNUName

STRING

empty

cwmp set

stunuser
username

STUN server user name

TR111STUNpwd

STRING

empty

cwmp set
stunpwd
password

STUN server pwd

Note

: Many other parameter is define in file:

TB30_Config File Syntax_Vxxxx_modified.doc

For large-scale installations in case many phones need to be connected to an ACS it is
strongly recommended to use the TB30 Autoprovision method. Setting the vaue in [cwmp]
part in common config file. And the detail APS flow please refer to TB30

AutoProvisioning-

Vxxxx.pdf

Summary of Contents for TB30











































































































































































































































































Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands

Technicolor TB30, Administrator'S Manual

Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands