Technicolor TB30 Administrator'S Manual Download Page 148

Page: 148 / 266

TB30s SIP Administrator Guide v1.3

Page 141 of 259

In Ringing (During call incoming) state

TB30 display the Caller and the Redirecting name alternatively on the
screen, and the redirecting name will be displayed in reverse video. The time

interval for the swap will be in 1 second.
If the diversion header has Redirecting party Name, phone should display

“Bob the Manager”, but if it doesn‟t have Redirecting party Name, phone
should display Number “81000541”.

In Talking state:

TB30 display the Caller name with number.

In Call log:

The call log list shows the detail of caller information.

Remark:

If the phone number of “Bob the manager” is saved in phone book, the
display should show the name in the phone book.

Only top header is showed.

Feature Activation

Via APS:

A new parameter will be introduced to activate/deactivate the feature of

redirecting identity and name presentation in [sip] section of both Common
and Specific-MAC config files.

DiversionHeaderFlag

= <0|1>,

Where,

0 is disable (default setting),
1 is enable

[sip]

…..

DiversionHeaderFlag =

// by default, disable

DiversionHeaderFlag =

// Diversion header is supported

…...

Via Telnet

To configure, open a command line console, and telnet the phone.

Summary of Contents for TB30











































































































































































































































































Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands

Technicolor TB30, Administrator'S Manual

Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands