Technicolor TB30 Administrator'S Manual Download Page 78

Page: 78 / 266

TB30s SIP Administrator Guide v1.3

Page 71 of 259

app_logo_bmp= http://path/xxxx.bmp

Another new parameter is added for logo on/off. This parameter is configurable in common config file

and telnet.

Config file: LogoDisplay = 0/1 (0: Off - Default, 1: On)
Telnet:

lcdui set LogoDisplay 0/1

Remark: if there is no bitmap downloaded, even it is on; it will be the same as off.

Another new parameter is added for timeout for display logo. This parameter is configurable in
common config file and telnet.

Config file: LogoTimeOut = 10 ~ 255s (30s default)
Telnet:

lcdui set LogTimeOut 10 ~ 255

Summary of Contents for TB30











































































































































































































































































Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands

Technicolor TB30, Administrator'S Manual

Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands