manualshive.com logo in svg

Technicolor TB30, Administrator'S Manual

The Technicolor TB30 Administrator's Manual is a comprehensive and free resource for optimizing your TB30 experience. Download this essential manual from manualshive.com to access step-by-step instructions, troubleshooting tips, and in-depth explanations, ensuring seamless operation and maximum productivity with your Technicolor TB30 device.

Share
Download
background image

 

 
TB30s SIP Administrator Guide v1.3  

 

Page 176 of 259 

 

 

 
Once A is in a call with the "focus UA", it could add another participant (D) in 

the same way: 

 
 

9. A press “Conf” soft key then enters D phone’s number.

 

 
10. D replies, A and D are in a 2nd call. 
 

11. A press “Conf” again.

 

 
10. A sends REFER to D to move to conference ID (as described in section 5.6 of the rfc-4579). 
 

 
Another variant: 

 
1. A and B are in a call. 
 
2. C calls A 
 
3. A replies, A and C are in a 2nd call, B is on hold. 
 

4. A press “Join” to switch in conference mode.

 

 
5. Phone A shall send an INVITE to the Conference_Factory_URI.  
 

6. It will retrieve the “conference ID” either in the 200 OK or the 302 Moved response.

 

 
7. send REFER to B to move to conference ID (as described in section 5.6 of the rfc-4579) 

Summary of Contents for TB30











































































































































































































































































Reviews:

No comments

Related manuals for TB30

Sangoma S500 Series Quick Reference Manual preview
S500 Series
Brand: Sangoma Pages: 12
Unify OpenStage 20 T Quick Reference Card preview
OpenStage 20 T
Brand: Unify Pages: 2
Oval EL 2310-08E Series Instruction Manual preview
EL 2310-08E Series
Brand: Oval Pages: 80
UTStarcom GSM708 User Manual preview
GSM708
Brand: UTStarcom Pages: 54
Slider W50C Manual preview
W50C
Brand: Slider Pages: 27
Polycom VVX 411 Instructions preview
VVX 411
Brand: Polycom Pages: 2
D-mobiel DMW7 Manual preview
DMW7
Brand: D-mobiel Pages: 28
Alcatel Onetouch Idol 2S 6050Y Quick Start Manual preview
Onetouch Idol 2S 6050Y
Brand: Alcatel Pages: 23
DDM Brands ANDY AC4E Manual preview
ANDY AC4E
Brand: DDM Brands Pages: 74
Avaya one-X 9650 Quick Reference preview
one-X 9650
Brand: Avaya Pages: 3
Pantech PP4GA-160C User Manual preview
PP4GA-160C
Brand: Pantech Pages: 82
UTStarcom Shuttle CDM8964VM User Manual preview
Shuttle CDM8964VM
Brand: UTStarcom Pages: 39
AMGOO AM517 Manual preview
AM517
Brand: AMGOO Pages: 32
Telme C151 Manual preview
C151
Brand: Telme Pages: 102
TP-Link NEFFOS Y5 User Manual preview
NEFFOS Y5
Brand: TP-Link Pages: 61
mobilicity Totem User Manual preview
Totem
Brand: mobilicity Pages: 99
GENERAL MOBILE DST13 User Manual preview
DST13
Brand: GENERAL MOBILE Pages: 56
Geemarc amplipower 60+ Manual preview
amplipower 60+
Brand: Geemarc Pages: 44

Brands by name

Popular brands

Load more brands