Technicolor TB30 Administrator'S Manual Download Page 113

Page: 113 / 266

TB30s SIP Administrator Guide v1.3

Page 106 of 259

CCBS Enable/Disable

A new parameter is added for CallBack feature. This parameter is configurable in common
config file and telnet.

auto_cb = 0/1

// 1: Enable CallBack feature

// 0: Disable CallBack feature

The default value is 1.

Via APS

APS in [ipp] section of both Common and Specific-MAC config files with the

new parameter –

auto_cb

[ipp]
…

auto_cb=1

// Enable (default)

…

Via Telnet

To configure, open a command line console, and telnet the phone:

Example:

Auto_cb is set to enable (

lcdui set auto_cb 1

)

Auto_cb is set to disable. (

lcdui set auto_cb 0

)

Then type

commit

and then

activate

to apply the change.

Date

Hour

Icons

Remote Unavailable!

XXXXXXXX

CBack

Back

Date

Hour

Icons

Remote Unavailable!

XXXXXXXX

Back

[administrator]# lcdui set auto_cb 1
LcdUi Set Command OK!

[administrator]#

[administrator]# lcdui set auto_cb 0
LcdUi Set Command OK!

[administrator]#

Summary of Contents for TB30











































































































































































































































































Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands

Technicolor TB30, Administrator'S Manual

Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands