Technicolor TB30 Administrator'S Manual Download Page 97

Page: 97 / 266

TB30s SIP Administrator Guide v1.3

Page 90 of 259

Feature Activation

Via APS

APS in [sys] section of both Common and Specific-MAC config files with all
MGC parameter.

MGC_service = 0

disable (default)

[sys]
…

MGC_service=0

// Disable (default)

…

MGC_service = 1

Hua Wei Softswitch PSTN handling

[sys]
…

MGC_service=1

// Hua Wei Softswitch

…

MGC_service = 2

MGC Cirpack Service

[sys]
…

MGC_service=2

Dial_Dtmf_Code=#5

Alternate_Dtmf_Code=#2

Rel_Libretre_Dtmf_Code=#0

Ans_Libretre_Dtmf_Code=#1

Transfer_Dtmf_Code=#4

Conference_Dtmf_Code=#3

…

Via Telnet

To configure, open a command line console, and telnet the phone:

Example:

MGC_service is set to disable (

sys set mgc_service 0

)

MGC_service is set to Hua Wei Softswitch PSTN handling (

sys set

mgc_service 1

)

MGC_service is set to Cirpack MGC Service (

sys set mgc_service 2

)

Then type

commit

and then

activate

to apply the change.

[administrator]# sys set mgc_service 2
[OK] Set OK

[administrator]#

[administrator]# sys set mgc_service 0
[OK] Set OK

[administrator]#

[administrator]# sys set mgc_service 1
[OK] Set OK

[administrator]#

Summary of Contents for TB30











































































































































































































































































Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands

Technicolor TB30, Administrator'S Manual

Search results

Summary of Contents for TB30

Reviews:

Related manuals for TB30

Brands by name

Popular brands