5
WY0
1
-0740E
Y-2.
Y-2.
Air Bleeding Procedure
6. Hydraulic pilot circuit
6.
1
Swing
Set the hydraulic oil temperature to 50
o
C (
1
22
o
F) or
higher, set the PTO switch and the swing brake
switch to ON, let the engine idle, and move the
swing control lever fully to the right-swing side. Keep
the above conditions for 20 seconds or more for
bleeding. Proceed the same steps by moving the
swing control lever to the left-swing side.
6.2 Elevating
Pull out the connector of the AML vent solenoid. Set
the hydraulic oil temperature to 50
o
C (
1
22
o
F) or
higher, set the PTO switch to ON, let the engine idle,
and move the boom elevating control lever fully to
the boom lowering side. Keep the above conditions
for 20 seconds or more for bleeding. Proceed the
same steps by moving the boom elevating control
lever to the boom raising side.
6.3 Telescoping
Pull out the connector of the AML vent solenoid. Set
the hydraulic oil temperature to 50
o
C (
1
22
o
F) or
higher, set the PTO switch to ON, let the engine idle,
and move the boom telescoping control lever fully to
the retraction side. Keep the above conditions for 20
seconds or more for bleeding. Proceed the same
steps by moving the boom telescoping control lever
to the boom extension side.
6.4 Winch (main and aux.)
[NOTICE]
Bleed the main and auxiliary winch circuits by
following the procedures below. The procedures are
common to the both circuits.
Pull out the connector of the AML vent solenoid. Set
the hydraulic oil temperature to 50
o
C (
1
22
o
F) or
higher, set the PTO switch to ON, let the engine idle,
and move the hoist control lever fully to the hoist-up
side. Keep the above conditions for 20 seconds or
more for bleeding. Proceed the same steps by
moving the hoist control lever to the hoist-down side.
7. Oil cooler motor
Pour the hydraulic oil through the drain port into the
casing until the oil flows out.
8. Air condition motor (option)
Pour the hydraulic oil through the drain port into the
casing until the oil flows out.
△
2
345-80
1
-02000
△
0
345-80
1
-00500
Summary of Contents for TT-800XXL1
