manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 94 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 94

Return To Table of Contents

94

2141-209-002 REV H

www.stryker.com

Service Information

BRAKE CONTROL BOARD REMOVAL AND REPLACEMENT - (FOOTBOARD)

Tools Required:

 

•  Phillips Screwdriver #2
•  Stubby Phillips Screwdriver #2
•  Small Slotted Screwdriver
•  Utility Knife
•  ESD System

Procedure: 
Note: ESD protection is required for this procedure.

1.  Remove the footboard assembly and place onto a nearby work surface, face down.
2.  Using a small slotted screwdriver or a utility knife, remove the rear footboard label.

Note: This label will need to be replaced with a new label (QDF27-2756).

3.  Using a Phillips screwdriver, remove the six screws securing the footboard display panel to the footboard.
4.  Pivot the display panel up. 
5.  Using a stubby Phillips screwdriver, remove the two screws from the bottom of the display panel.
6.  Hold the display panel and footboard assembly together and flip the footboard assembly over, with the display 

panel facing up.

7.  Carefully remove the display panel from the footboard assembly. Rotate over to display the circuit boards.
8.  Using a Phillips screwdriver, remove the two screws that secure the Wi-Fi antenna P-clamps to the brake control 

board.

9.  Using a Phillips screwdriver, remove the remaining four screws that secure the brake control board to the footboard 

display housing.

10.  Disconnect the brake control cable from the brake control board.
11.  Remove the brake control board.
12.  Reverse the procedure to install the new brake control board.
13.  Test all bed functionality before returning the bed to service.

Rear Footboard Back Label

Screws

Brake Control Board

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments