Stryker InTouch FL27 series Maintenance Manual Download Page 33

Page: 33 / 252

Return To Table of Contents

www.stryker.com

2141-209-002 REV H

Maintenance Menu Guide

INTOUCH CONFIGURATION SCREEN (CONTINUED)

A. Bed Calibration (Continued)

24. Press the

Fowler Up

button until the Fowler reaches

the highest height, next press the

Gatch Up

button

until the Gatch reaches its highest height, lastly
press the

Foot Up

button until the foot section

reaches its highest height (refer to Figure 21
below). The foot section should be at a flat position.

25. Press the

Next

button when done.

26. The “Do Not Touch Bed” screen will appear as

shown in Figure 22.

Gatch Up

Fowler Up

Figure 21: Head Siderail Control Panel -

(Right Side Shown)

QDF27-2237

Foot Up

Figure 22: Do Not Touch Bed Screen

Bed Calibration

Cancel

Do Not

Touch Bed

Summary of Contents for InTouch FL27 series





























































































































































































































































Search results

Summary of Contents for InTouch FL27 series

Reviews:

Stryker InTouch FL27 series, Maintenance Manual, Page: 33 / 252

Search results

Summary of Contents for InTouch FL27 series

Reviews: