manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 7 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 7

www.stryker.com

2141-209-002 REV H

7

Table of Contents

Assembly Drawings (Continued)
Litter Assembly, Standard Cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

150

Litter Assembly, Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

151

120V Electric System  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

157

Coiled Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

158

Litter Assembly, Foot End, with Mattress Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

159

Standard Outlet  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160

Litter Assembly, Optional Dual 120V Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

161

CPR Assembly, Mechanical  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

163

Handle Assembly (Model 2131 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

168

Zoom

®

 Handle Assembly (Model 2141 Only)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

169

Zoom

® 

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

171

Optional No Head End Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

172

Optional Head End Control Panel Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

173

Siderail Mounting Assembly, Head End  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

175

Standard Siderail Assembly, Head End, Right  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

176

Standard Siderail Assembly, Head End, Left  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

180

Standard Siderail Assembly, Labeling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

184

Optional Siderail Assembly, Head End, with Speaker/

i

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

185

Optional Siderail Assembly, Head End, with Speaker/with NC/with 

i

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

186

Optional Siderail Assembly, Head End, with Speaker/

i

Audio/IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

188

Optional Siderail Assembly, Head End, with Speaker/with NC/with 

i

Audio/with 

i

Bed

®

 Wireless. . . . . . . . . . . . . . .

189

Siderail Mounting Assembly, Foot End. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

193

Standard Siderail Assembly, Foot End, Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

194

Standard Siderail Assembly, Foot End, Left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

197

Standard Siderail Assembly without 

i

Bed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

200

Optional Siderail Assembly with 

i

Bed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201

Headboard and Footboard Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

202

Standard Footboard Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

203

Footboard Assembly without

 i

Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

205

Footboard Assembly with

 i

Bed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

208

Footboard Assembly with

 i

Bed and Wi-Fi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

211

Bed Extender - FA64234-XXX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

214

Bed Extender Pad with Position Pro Mattress - DM64196-XXX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

215

Bed Extender Pad with XPRT™ Mattress - DM64197-XXX  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

215

Line Management Clip - FA64210-XXX  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

216

IV Pole Assembly, Permanent - FA64221-XXX/FA64238-XXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

217

IV Pole Ass’y, Dual Head End, Permanent - FA64202-XXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

218

Monitor Tray Assembly - FA64214-XXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

220

Upright Oxygen Bottle Holder Assembly - FA64187-XXX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

221

Right-Fit Oxygen Bottle Holder Assembly - FA64203  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

222

Pendant Assembly with Motion Control  - FA64228-XXX  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

223

Pendant Assembly with Motion Control/NC  - FA64226  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

224

Pendant Assembly with Motion Control/Smart TV  - FA64227. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

225

Pendant Assembly with Motion Control/NC/Smart TV  - FA64225. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

226

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments