manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 106 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 106

Return To Table of Contents

106

2141-209-002 REV H

www.stryker.com

IR MODULE REMOVAL AND REPLACEMENT - (LITTER) (OPTIONAL)

Tools Required:

 

•  Phillips Screwdriver #2
•  Diagonal Pliers
•  ESD System

 

 

 

 

 

 

 

 

 

 
Procedure: 
Note: ESD protection is required for this procedure.

1.  Plug the bed into a wall outlet.
2.  Raise the bed to the full up position.
3.  Raise the fowler to the full up position.
4.  Unplug the bed power cord from the wall outlet.
5.  Turn the battery disconnect switch off.
6.  Remove the headboard from the bed.
7.  If the optional head end IV pole is present, use a 1/2” socket and 3/8” drive ratchet to remove the IV pole.
8.  Using a Phillips screwdriver, remove the six screws that secure the head end frame cover to the head end frame.
9.  Remove the head end frame cover and set aside.
10.  Using a Phillips screwdriver, remove the two screws that secure the right IR module and gasket to the head end 

frame.

Note: Ensure the IR module cable is routed in the wire track before reinstallation.

11.  Using a Phillips screwdriver, remove the two screws that secure the left IR module and gasket to the head end 

frame.

12.  Using diagonal pliers, cut the cable tie that secures the IR module cables below the head end frame.
13.  Disconnect the right IR module cable from connector J5 on the headwall communication board.
14.  Disconnect the left IR module cable from connector J2 on the headwall communication board.
15.  Reverse the procedure to install the new IR modules.

Note: Route both right and left IR module cables into the head end frame through the matching right and left 
Zoom

®

 handle cable cutouts in the head end frame.

16.  Test all bed functionality before returning the bed to service.

He

ad

  

Fo

ot

Head End Frame

Right IR Module

Gasket

Headwall 

Communication 

Board

Service Information

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments