manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 22 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 22

Return To Table of Contents

22

2141-209-002 REV H

www.stryker.com

Setup

To unpack your product, see the unpacking instructions that are attached to the product inside of the shipping crate.

 WARNING

•  Always allow the product to reach room temperature before conducting any setup or testing functional operations 

to prevent permanent product damage.

•  Always operate the product when all operators are clear of the mechanisms.
•  Always properly handle the power cord to avoid the risk of entanglement, damage to the power cord, or potential 

shock hazards. If the power cord is damaged, immediately remove the product from service and contact the 
appropriate maintenance personnel.

•  Do not attach the power cord to any moving parts of InTouch.
•  Always unplug the power cord, turn the battery switch to the 

OFF (O)

 position, press the N/Brake Off button, and 

call maintenance if unanticipated motion occurs.

 CAUTION

Always plug the product directly into a properly grounded, three-prong receptacle. You can only achieve grounding 
reliability when you use a hospital-grade receptacle. This product is equipped with a hospital-grade plug for protection 
against electric shock hazard.

To turn on the product:

1.  Plug the power cord into a properly grounded, hospital-grade wall outlet.
2.  Turn the battery switch to the 

ON (|)

 position.

Before placing the product into service, make sure that these components are working properly:

1.  Visually inspect the product for any signs of shipping damage.
2.  Flip down and depress the manual brake pedal and make sure that the neutral, drive, and brake functions of the 

manual brake pedal hold.

3.  Press BRAKE on each control panel and make sure that the neutral, drive, and brake functions of the electronic 

brake hold.

4.  Test the Zoom drive system (Model 2141).
5.  Raise and lower the siderails to make sure that they move smoothly and lock securely in the full up position.
6.  Press each button on the head end control panel (optional), motion control panel, brake control panel, footboard 

control panel, and patient control pendant (optional) to make sure that each function operates properly.

7.  Make sure that the footboard operates properly.
8.  Make sure that the scale system operates properly.
9.  Make sure that the bed exit system operates properly.
10.  Make sure that the CPR release pedal operates properly.
11.  Make sure that the support surface operates properly (optional).
12.  Make sure that optional accessories are installed and operate as described.

 WARNING

Always unplug the product power cord from the wall when using oxygen administering equipment. Possible fire hazard 
exists when this product is used with oxygen administering equipment other than nasal, mask type, or half bed-length 
tent type.

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments