manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 108 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 108

Return To Table of Contents

108

2141-209-002 REV H

www.stryker.com

Service Information

WI-FI BOARD REMOVAL AND REPLACEMENT - (FOOTBOARD) (OPTIONAL) (CONTINUED)

13.  Reverse the procedure to install the new display.
14.  On the footboard display screen, press the Wi-Fi antenna icon located in the lower left corner of the display.
15.  Record the MAC address of the newly installed Wi-Fi board.
16.  Provide the MAC addresses of the old Wi-Fi board and the new Wi-Fi board, along with the serial number of the 

unit, to the facility’s IT department.

Note: The MAC address for the record will need to be updated from the old Wi-Fi board MAC address to the 
new Wi-Fi board MAC address. Failing to do so will prevent the unit from connecting to the facility’s wireless 
network. 

17.  Configure the bed’s Wi-Fi settings with hospital network information.

a. 

Access the Configuration Menu by referencing the procedure on 

page 25

.

b. 

On the Configuration Menu screen, press Wi-Fi Configuration.

c. 

Press the Advanced tab.

d. 

Press Reset.

e. 

Press OK.

f. 

Press Save.

g. 

In the pop-up message screen, press Close.

h. 

Using the Wi-Fi configuration tabs, configure the bed to the hospital network settings.

i. 

Once configured, press Save.

j. 

In the pop-up message screen, press Close.

18.  Press the Wi-Fi antenna icon on the bottom left corner of the touch screen.

a.  Verify the bed has connected to the hospital network by looking for brackets around the antenna in the 

Wi-Fi icon in the bottom left corner of the touch screen. 

b.  Press the Wi-Fi icon in the bottom left corner of the touch screen and verify the bed received a proper 

hospital issued IP address.

19.  Test all bed functionality before returning the bed to service.

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments