manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 60 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 60

Return To Table of Contents

60

2141-209-002 REV H

www.stryker.com

Error Codes

Touch Screen Error Messages Name Definition

Scale Chip Failure

Control board is bad (Replace Control Board).

Tilt base over range

Verify if tilt sensor is still in place. Inspect for a damaged or improperly 
assembled tilt sensor or recalibrate bed.

Tilt Error Base

Angle sensor is damaged (Replace sensor).

Tilt Error Foot

Angle sensor is damaged (Replace sensor).

Tilt Error Gatch

Angle sensor is damaged (Replace sensor).

Tilt Error Head

Angle sensor is damaged (Replace sensor).

Tilt Error HiLo Foot

Angle sensor is damaged (Replace sensor).

Tilt Error Trend

Angle sensor is damaged (Replace sensor).

Tilt foot over range

Verify if tilt sensor is still in place. Inspect for a damaged or improperly 
assembled tilt sensor or recalibrate bed.

Tilt gatch over range

Verify if tilt sensor is still in place. Inspect for a damaged or improperly 
assembled tilt sensor or recalibrate bed.

Tilt head over range

Verify if tilt sensor is still in place. Inspect for a damaged or improperly 
assembled tilt sensor or recalibrate bed.

Tilt hiLo foot over range

Verify if tilt sensor is still in place. Inspect for a damaged or improperly 
assembled tilt sensor or recalibrate bed.

Tilt trend over range

Verify if tilt sensor is still in place. Inspect for a damaged or improperly 
assembled tilt sensor or recalibrate bed.

Zoom® time out for switch

Verify wiring to Zoom® motor.

Wi-Fi / IR Communication Error

Definition

Wireless Adapter Failure

Unable to detect or communicate with Wi-Fi radio. Check assembly or 
cabling of Wi-Fi card in footboard or replace Wi-Fi card or footboard.

DHCP Error: Unable to obtain IP 
Address

Bed is not able to connect to the wireless network. Check wireless network 
settings and Wi-Fi configuration of bed.

Unable to connect to network

Bed is not able to connect to the wireless network. Check wireless network 
settings and Wi-Fi configuration of bed.

Internal Communication Error

Internal software failure. Software corruption may have occurred. Re-upload 
software or replace footboard.

Wi-Fi Settings corrupted

Reconfigure Wi-Fi settings in bed.

Bed Serial Number not available

Configure bed serial number.

Left IR Module not detected

Unable to detect IR module. Check cabling or replace the IR module.

Right IR Module not detected

Unable to detect IR module. Check cabling or replace the IR module.

IR Interface Board not detected

Unable to detect the Room interface board. Check cabling or replace the 
Room interface board.

IR Crosstalk detected

Crosstalk detected with iBed Locator Wall module. Verify placement of IR 
modules on bed or wall modules.

Isolibrium Error Code

Definition

0100

Sensor Board communication failure

0101

Sensor Board EEPROM corruption

0102

Sensor Board not calibrated

0200

GUI CANopen Heartbeat Lost

0400

EEPROM corruption

0500

Ambient temperature sensor failure

0501

Ambient temperature out of range

0600

Pressure sensor failure

0601

Seat Left pressure sensor failure

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments