Stryker InTouch FL27 series Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 252

Stryker InTouch FL27 series Maintenance Manual Download Page 19

Return To Table of Contents

www.stryker.com

2141-209-002 REV H

19

Summary of Safety Precautions

• Always lock the control panel when the patient is unattended, or when a patient’s condition requires greater safety

measures for their condition.

• Do not use iBed® Awareness as a lock indicator for siderails. iBed® Awareness is only intended to detect the

position of the siderails. It is not intended to replace patient monitoring protocol.

• The iBed® Awareness LED light bars are only intended to monitor the product status and parameter conditions. It

is not intended to replace patient monitoring protocol.

• You must physically verify that the siderails are locked before arming iBed® Awareness.
• Always securely set the footboard connector on the optional bed extender into the footboard connector slot at the

foot end of the product.

•  Do not pinch the power cord or cables when installing the optional bed extender.
•  Do not sit on the optional bed extender. This may cause the product to flip.
•  Do not allow the optional line management clip to interfere with a mechanical or electronic mechanism of the

product.

•  Do not pinch tubes inside the clip.
•  Do not clean the clip with a liquid solution.
•  Always adjust the scale or bed exit system if an option is added while the scale or bed exit system is armed.
•  Do not place objects that exceed 40 lb (18 kg) onto the optional monitor tray.
•  Do not exceed the 150 lb (68 kg) load capacity for the tray support pole.
•  Do not clean, service, or perform maintenance while the product is in use.
•  Always unplug the power cord and turn the battery switch to the OFF (O) position before cleaning, servicing, or

performing maintenance.

• Always immediately unplug the power cord from the wall outlet when large spills occur near the circuit boards,

cables, and motors. Remove the patient from the product, clean up the fluid, and have service personnel completely
inspect the product. Fluids can cause unpredictable operation and decreased functionality of any electrical product.
Do not return the product to service until it is completely dry and has been thoroughly tested for safe operation.

WARNING (CONTINUED)

«
...
17
18
19
20
21
...
»

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments