manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 6 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 6

6

2141-209-002 REV H

www.stryker.com

Table of Contents

CPU/Power Board - QDF75-0440 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

Fuse Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64

Bed Electrical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

65

Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Bed lift Actuator (Head) Removal and Replacement - (Base). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Bed lift Actuator (Foot) Removal and Replacement - (Base)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

Fowler Actuator  Removal and Replacement - (Litter)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86

Gatch Actuator Removal and Replacement - (Litter)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87

Foot Actuator Removal and Replacement - (Litter)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

88

Zoom®  Drive Actuator Removal and Replacement (2141 Model Only) - (Base) . . . . . . . . . . . . . . . . . . . . . . .

89

CPU / Power Board Removal and Replacement - (Litter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

90

Load Cell (Head End)  Removal and Replacement - (Litter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91

Load Cell (Foot End)  Removal and Replacement - (Litter)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

92

Display Removal and Replacement - (Footboard)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

93

Brake Control Board Removal and Replacement - (Footboard)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

94

Function Selection/LED Board  Removal and Replacement - (Footboard)  . . . . . . . . . . . . . . . . . . . . . . . . . . .

95

Touch Screen Removal and Replacement - (Footboard)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

96

Battery Removal and Replacement - (Footboard)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

97

Brake / Neutral / Drive Potentiometer Removal and Replacement - QDF27-2024  . . . . . . . . . . . . . . . . . . . . . .

98

Battery Removal and Replacement - (Litter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

99

Fowler Angle Sensor  Removal and Replacement - (Litter)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

Gatch Angle Sensor  Removal and Replacement - (Litter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

101

Foot Angle Sensor  Removal and Replacement - (Litter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

102

Base Angle Sensor Removal and Replacement - (Base) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

103

Trend Angle Sensor  Removal and Replacement - (Litter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

104

Headwall Communication Board Removal and Replacement - (Litter)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105

IR Module Removal and Replacement - (Litter) (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

106

Wi-Fi Board Removal and Replacement - (Footboard) (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

107

Base Assembly, Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

109

Base Assembly, Brake  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

111

Base Assembly, Caster Lock (Model 2131 Only)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

114

Base Assembly, Caster Non-Lock (Model 2141 Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

115

Angle Sensor Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

116

Base Assembly, Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

117

Base Assembly, Zoom®  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

123

Base Assembly, Zoom

®

 Drive (Model 2141 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

125

Bed Labeling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

127

Lift Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

131

Spring Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

135

Litter Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

136

Litter Assembly, Interior Frame  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

140

Litter Assembly with Serial Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

143

Litter Assembly, Upper Frame   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

144

Litter Assembly, Foot End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

146

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments