Stryker InTouch FL27 series Maintenance Manual Download Page 52 | Manualshive

Page: 52 / 252

Stryker InTouch FL27 series Maintenance Manual Download Page 52

Return To Table of Contents

52

2141-209-002 REV H

www.stryker.com

Problem / Failure

Recommended Action

No Bed Up Motion.

FOOT

1.

Put the bed into the Bed Calibration menu.
A. Using one of the head siderails, push the trend button.

I. If the foot lift motor runs up, recalibrate the bed (refer to

the Bed Calibration procedures located on

page 25

).

a. If recalibration does not work, replace the litter angle
sensor and recalibrate.

II. If the foot lift motor does not run up, check for 24VDC at

connector J6 while pressing the trend button. Black lead
to pin 1, red lead to pin 2.
a. If voltage is present, replace the motor.
b. If voltage is not present, replace the CPU/Power board.

HEAD

1.

Put the bed into the Bed Calibration menu.
A. Using one of the head siderails, push the bed up button.

I. If the head lift motor runs up, recalibrate the bed (refer to

the Bed Calibration procedures located on

page 25

).

a. If recalibration does not work, replace the litter angle
sensor and recalibrate.

II. If the head lift motor does not run up, check for 24VDC at

connector J4 while pressing the trend button. Black lead
to pin 1, red lead to pin 2.
a. If voltage is present, replace the motor.
b. If voltage is not present, replace the CPU/Power board.

No Bed Down Motion.

FOOT

1.

Put the bed into the Bed Calibration menu.
A. Using one of the head siderails, push the reverse trend button.

I. If the foot lift motor runs down, recalibrate the bed (refer

to the Bed Calibration procedures located on

page 25

).

a. If recalibration does not work, replace the litter angle
sensor and recalibrate.

II. If the foot lift motor does not run down, check for 24VDC

at connector J6 while pressing the reverse trend button.
Red lead to pin 1, black lead to pin 2.
a. If voltage is present, replace the motor.
b. If voltage is not present, replace the CPU/Power board.

HEAD

1.

Put the bed into the Bed Calibration menu.
A. Using one of the head siderails, push the bed down button.

I. If the head lift motor runs down, recalibrate the bed (refer

to the Bed Calibration procedures located on

page 25

).

a. If recalibration does not work, replace the litter angle
sensor and recalibrate.

II. If the head lift motor does not run down, check for 24VDC

at connector J4 while pressing the trend button. Red lead
to pin 1, black lead to pin 2.
a. If voltage is present, replace the motor.
b. If voltage is not present, replace the CPU/Power board.

Troubleshooting

BED TROUBLESHOOTING

«
...
50
51
52
53
54
...
»

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments