manualshive.com logo in svg

Stryker InTouch FL27 series, Maintenance Manual, Page: 53 / 252

Share
Download
Stryker InTouch FL27 series Maintenance Manual Download Page 53

Return To Table of Contents

www.stryker.com

2141-209-002 REV H

53

Problem / Failure

Recommended Action

No Fowler Up Motion.

1.

Put the bed into the Bed Calibration menu.
A.  Using one of the head siderails, push the fowler up button.

I.  If the fowler motor runs up, recalibrate the bed (refer to 

the Bed Calibration procedures located on 

page 25

). 

a.  If recalibration does not work, replace the fowler angle 
    sensor and recalibrate.

II.  If the fowler motor does not run up, check for 24VDC at 

connector J5 while pressing the fowler up button.  Black 
lead to pin 1, red lead to pin 2. 
a.  If voltage is present, replace the motor. 
b.  If voltage is not present, replace the CPU/Power 
board. 

No Fowler Down Motion.

1.

Put the bed into the Bed Calibration menu.
A.  Using one of the head siderails, push the fowler down button.

I.  If the fowler motor runs down, recalibrate the bed (refer to 

the Bed Calibration procedures located on 

page 25

). 

a.  If recalibration does not work, replace the fowler angle 
    sensor and recalibrate.

II.  If the fowler motor does not run down, check for 24VDC 

at connector J5 while pressing the fowler down button.  
Red lead to pin 1, black lead to pin 2. 
a.  If voltage is present, replace the motor. 
b.  If voltage is not present, replace the CPU/Power 
board. 

No Gatch Up Motion.

1.

Put the bed into the Bed Calibration menu.
A.  Using one of the head siderails, push the gatch up button.

I.  If the gatch motor runs up, recalibrate the bed (refer to 

the Bed Calibration procedures located on 

page 25

). 

a.  If recalibration does not work, replace the gatch angle 
    sensor and recalibrate.

II.  If the gatch motor does not run up, check for 24VDC at 

connector J3 while pressing the gatch up button.  Red 
lead to pin 1, black lead to pin 2. 
a.  If voltage is present, replace the motor. 
b.  If voltage is not present, replace the CPU/Power 
board. 

Troubleshooting

BED TROUBLESHOOTING

Summary of Contents for InTouch FL27 series





























































































































































































































































Reviews:

No comments