Stryker InTouch FL27 series Maintenance Manual Download Page 90

Page: 90 / 252

Return To Table of Contents

2141-209-002 REV H

www.stryker.com

Tools Required:

•  Phillips Screwdriver #2
•  ESD System
•  3/8” Nutdriver

Procedure:

1. Plug bed into wall outlet.
2. Set the brakes using one of the brake control locations

or by using the manual brake pedal.

3. Raise the bed to the full upright position.
4. Remove the mattress assembly or fold back to expose

the foot section.

5. Using a Phillips screwdriver, remove the two screws

(reference drawing, item A and B) securing the
electrical cover and remove the cover.

Note: Use caution as the cover is large and heavy.

6. Unplug the bed from the wall outlet and turn battery

switch OFF. The bed should now have no power.

7. Using an ESD system, properly ground yourself.
8. Unplug all cable connections from the CPU/Power

board.

9. Using a 3/8” nutdriver and a Phillips screwdriver, unscrew

the four screws (C) securing the metal CPU/Power
board mounting plate to the electrical tray (reference
drawing above).

10. Remove CPU/Power board and discard.
11. Reverse steps 9-4 to install the new CPU/Power board

(QDF75-0440).

12. Plug bed back into wall outlet and turn the battery switch

back ON.

13. Configure bed options (refer to the Bed Options

Configuration procedure on

page 39

14. Configure the bed serial number (refer to the Serial

Number Configuration procedure on

page 40

15. Recalibrate the bed by referring to the Bed Calibration

procedure on

page 25

16. Test all bed functionality prior to putting the bed back

into service.

Service Information

CPU / POWER BOARD REMOVAL AND REPLACEMENT - (LITTER)

Electrical Cover

CPU/Power board

Summary of Contents for InTouch FL27 series





























































































































































































































































Search results

Summary of Contents for InTouch FL27 series

Reviews:

Stryker InTouch FL27 series, Maintenance Manual, Page: 90 / 252

Search results

Summary of Contents for InTouch FL27 series

Reviews: