manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 83 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 83

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

81 

9.2.8 Parameter Group 08 - Display Filters 

 
The parameters in this group select the time constants for the digital filters used that are applied to 
the load cell and output signals. 
 
 

P 08.01  LC Filter

 

Default: 4.00 sec  

Min: 0.25 sec 

Max: 300.00 sec 

 
This parameter sets the amount of digital filtering used on the load cell signals.  It is similar to the 
196NT Setup 19 Weight Signal Filter.   
 
This parameter is normally set to 4 seconds. 
 
 

P 08.02  I-Display

 

Default: 1.0 sec  

Min: 0.0 sec 

Max: 600.0 sec 

 
This parameter sets the amount of digital filtering used on the feedrate value displayed on the display, 
EasyServe and field bus interface. It is similar to the 196NT Setup 20 Feedback Signal Filter.   
 
This parameter is normally set to 1 second. 
 
 

P 08.03  I-Analog Output 

Default: 1.0 sec  

Min: 0.0 sec 

Max: 600.0 sec 

 
This parameter sets the amount of digital filtering used on the feedrate signal sent to the analog 
output channel. It is similar to the 196NT Setup 20 Feedback Signal Filter.  This parameter is 
normally set to 1 second. 
 
 

P 08.04  Feedback filter override threshold

  Default: 15%  

Min: 0.0% 

Max: 200.0% 

 
This parameter specifies point at which the point at which the feedback filter is overridden and the 
actual feedrate is displayed.  This is used so that large changes are displayed quickly. This parameter 
is the same as 196NT Setup 21 (Feedback filter override threshold). 
 
This parameter is normally set to 15%. 
 
 

P 08.05  Belt Load

 

Default: 1.0 sec  

Min: 0.0 sec 

Max: 600.0 sec 

 
This parameter sets the amount of digital filtering used on the belt load signal sent to the analog 
output channel. 
 
This parameter is normally set to 1 second. 
 
 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments