manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 128 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 128

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

126 

9.2.20 Parameter Group 20 - Reports 

 
The parameters in this group are used to specify the time that material total data logging occurs. 
 
 

P 20.01  Hourly Start 

Default: 0 min 

Min: 0 min 

Max: 59 min  

 
This parameter specifies the time that the hourly total is saved to the total data logging system.  It is 
the same as Setup 37 (Hourly total time) on the 196NT. 
 
This parameter is set according to customer preference. 
 
 

P 20.02  Daily Start 

Default: 0 min 

Min: 0 min 

Max: 1493 min  

 
This parameter specifies the time that the daily total is saved to the total data logging system.  It is the 
same as Setup 38 (Daily total time) on the 196NT. 
 
This parameter is set according to customer preference. 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments