manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 115 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 115

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

113 

P 16.05  DO: Feeder Run Forward 2 

Default:  n/a (not used - Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the second digital output used to start the feeder running forward. This 
output is a duplicate of P 16.04 DO: Feeder Run Forward. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

P 16.06  DO: Feeder Run Reverse 

Default: DO 2 - High (Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to start the feeder in reverse. This output is similar to 
the K2 relay on the 196 NT. 
 
This parameter must be set to DO 2 – High and is connected to wires 156-158. 
 
 

P 16.07  DO: Feeder Run Reverse 2 

Default:  DO 3 - High (Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the second digital output used to start the feeder in reverse. This output is a 
duplicate of P 16.06 DO: Feeder Run Reverse. 
 
This parameter must be set to DO 3 – High and is connected to wires 159-161. 
 
 

P 16.08  DO: Start Pre-feeder 

Default: n/a (not used - Hidden) 

Options:  

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to start the pre-feeder. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments