manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 64 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 64

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

62 

P 02.13  Totalizer Increment

 

Default: 100.00 lb  

Min: 0.00 lb 

Max: 100,000 lb 

 
This parameter sets the weight associated with each Total Coal Integrator (TCI) pulse.  It is the same 
as 196NT Setup 07 (Remote Totalizer Data Logging Increment). 
 
The TCI output frequency is based on parameter P02.11, parameter P02.12 and the actual feedrate.  
If the values selected for these parameters require an output frequency greater then the maximum 
frequency of the selected device, an error (MF 14 - P02.13) will be generated.  See parameter P02.12 
for more information. 
 
This parameter is normally set to either 100 Lbs or 100 Kgs. 
 
 

P 02.14  Remote Totalizer Pulse Width

 

Default: 0.100 s  

Min: 0.000 s 

Max: 10.000 s 

 
This parameter sets the duration of each Total Coal Integrator (TCI) pulse.  It is the same as 196NT 
Setup 35 (Remote Totalizer Pulse Width). 
 
The TCI output frequency is based on this parameter, parameter P02.11 and the actual feedrate.  If 
this combination of values requires an output frequency greater then the maximum frequency of the 
selected device, an error (MF 14 - P02.13) will be generated. 
 
The maximum pulse frequency can be calculated as: 
 
Frequency = ( P03.05 Maximum Feedrate) / ((3600) x ( P02.11)) 
 
Where the maximum feedrate is in lbs/hr and P02.11 is in lbs. 
 
When the TCI output is directed to an open collector or reed relay output the maximum possible pulse 
frequency is 10 Hz (P02.12 set to 0.05 sec).  When the TCI output is directed to a mechanical relay 
output the maximum possible pulse frequency is 1.0 Hz (P02.12 set to 0.5 sec).  When the pulse 
length (P02.12) is increased, these values are reduced. 
 
The maximum possible frequency (in Hz) is calculated as: 
 
Max. possible freq. = 1 / (2 X  P02.12 (in sec)) 
 
To insure that the TCI output works correctly the maximum pulse frequency must always be less then 
the maximum possible frequency. 
 
This parameter is normally set to 0.1 sec. 
 
 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments