manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 120 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 120

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

118 

P 16.25  DO: Remote CTRL 

Default: DO 4 High (Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to indicate that the feeder is in remote mode. This 
output is similar to the Kx relay on the 196 NT. 
 
This parameter must be set to DO 4 – High and is connected to wires 162-164. 
 
 

P 16.26  DO: Remote CTRL 2 

Default:  n/a (not used - Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to indicate that the feeder is in remote mode. This 
output is a duplicate of P 16.25 DO: Remote CTRL. 
 
This function is not used and this parameter should be set to n/a (not used). 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments