manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 124 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 124

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

122 

9.2.18 Parameter Group 18 - 2-Sensor Slip 

 
The parameters in this group control the DT-9 belt slip sensor system. This system is not currently 
supported and is disabled and hidden by default. 
 
 

P 18.01  2-Sensor Slip active

 

Default: NO (Hidden) 

 

Options:

 

NO 
YES  

 

 
Normally Hidden. 
 
This parameter is used to enable the DT-9 slip sensor system. 
 
The slip sensor system is not currently supported on the VCU 20104. This parameter should always 
be set to NO. 
 
 

P 18.02  Source Sensor 1    

Default: Speed (Hidden) 

 

Options: 

n/a (not used) 
DI 1 thru DI 12 – High/Low 

 
Normally Hidden. 
 
This parameter specifies the type of input used for the first of the two sensors used in slip detection.   
 
The slip sensor system is not currently supported and this parameter should always be set to Speed. 
 
 

P 18.03  DI: Sensor 1 

Default: n/a (not used - Hidden) 

Options: 

n/a (not used) 
DI 1 thru DI 12 – High/Low 

 
Normally Hidden. 
 
This parameter specifies the digital input used for the first slip sensor. It is only active if P18.02 
Source Sensor 1 is set to DI. 
 
The slip sensor system is not currently supported and this parameter should always be set to n/a   
(not used). 
 
 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments