manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 117 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 117

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

115 

P 16.13  DO: I-MAX 

Default: n/a (not used - Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to indicate that a high flow rate event is active. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

P 16.14  DO: Q-MIN 

Default: n/a (not used - Hidden) 

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to indicate that a low belt load event is active. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

P 16.15  DO: Q-MAX 

Default: n/a (not used - Hidden)  

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to indicate that a high belt load event is active.  
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

P 16.16  DO: v-MIN 

Default: n/a (not used - Hidden)  

Options: 

n/a (not used) 
DO 1 thru DO 13 - High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital output used to indicate that a low belt speed event is active. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments