manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Configuration And Operation Manual, Page: 112 / 158

Share
Download
Stock DISOCONT Tersus DT-9 Configuration And Operation Manual Download Page 112

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

110 

P 15.26  DI: Jog Forward 

Default: n/a (not used – Hidden) 

Options: 

n/a (not used) 
DI 1 thru DI 14 – High/Low 

 
Normally Hidden. 
 
This parameter specifies the digital input used to jog the feeder forward. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

P 15.27  DI: Jog Backwards 

Default: n/a (not used - Hidden) 

Options: 

n/a (not used) 
DI 1 thru DI 14 – High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital input used to jog the feeder in reverse. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

P 15.28  Event: External Event 2

 

Default: IG (Hidden) 

Event Group: SC 

Number: 06 

Options:  

IG 
A (Stop feeder) 
W1 (Warning – manual reset) 
W2 (Warning – Automatic reset) 

 
Normally Hidden.  
 
This parameter specifies the event that is generated when the input specified in P15.29 DI External 
Event 2 is active. 
 
This function is not used and this parameter should be set to IG (Ignore). 
 
 

P 15.29  DI: External Event 2 

Default: n/a (not used – Hidden) 

Options: 

n/a (not used) 
DI 1 thru DI 14 – High/Low 

 
Normally Hidden.  
 
This parameter specifies the digital input used to remotely generate External Event 2. 
 
This function is not used and this parameter should be set to n/a (not used). 
 
 

Summary of Contents for DISOCONT Tersus DT-9































































































































































Reviews:

No comments